[toc]
Introduction
This guide explains which drones you can use and how to plan and capture drone images effectively for Drone Capture. It covers best practices for selecting capture angles, ensuring sufficient image overlap, flying in a consistent way to support reliable processing results, and preparing Ground Control Point (GCP) targets for improved georeferencing accuracy.
Note: This article covers capture planning and execution. For step-by-step upload instructions, see the Upload drone photos with CupixConnect.
Before You Fly: Key Concepts to Understand
Drone Image Requirements
Drone Capture processes standard drone photos into georeferenced aerial datasets such as Orthomosaic, DSM, Point Cloud, and Mesh.
To be eligible for processing, drone images must meet the following requirements:
- Supported formats:
.jpg,.jpeg - Minimum of 6 images required to create an aerial map
- Maximum of 3,500 images per aerial map
- Images must include valid geolocation data (latitude, longitude, and altitude in the GPS EXIF metadata)
- Images must be captured using a consistent strategy and have sufficient overlap; refer to the best practices below for guidance.
Note: Image quality issues cannot be fully corrected during processing, so poor image quality may affect final results.
Nadir vs. Oblique Capture
Drone photos can be captured using two primary acquisition methods: Nadir and Oblique. Each method is suited to different output types and use cases .
Nadir Capture
Nadir capture refers to drone photos captured from directly above, with the camera pointing straight downward toward the ground.
Use nadir capture when your goal is to generate:
- Orthomosaic (Ortho): A georeferenced 2D aerial image corrected for distortion and scale
- Digital Surface Model (DSM): A height map representing terrain and surface elevations
Nadir capture is commonly used for site overviews, progress tracking, and measurements where consistent scale and top-down accuracy are required.
Oblique Capture
Oblique capture refers to drone photos captured at an angled view, with the camera tilted to include vertical surfaces.
Use oblique capture when your goal is to generate:
- Point Cloud: A 3D point-based reconstruction of the site
- Mesh: A 3D textured surface for realistic visualization
Oblique capture is typically used when 3D context is required, such as capturing building façades, vertical structures, or complex site geometry.
Supported Drones
The following drones are supported for creating aerial maps in Drone Capture.
Note: Newer models not included in this list may also be compatible if they meet the image requirements.
| Drone Series | Models Supported |
|---|---|
| DJI Inspire | Inspire 1, Inspire 2 |
| DJI Mavic Air | Mavic Air, Mavic Air 2, Air 2S, Air 3 |
| DJI Mavic Mini | Mavic Mini, Mini 2, Mini 3, Mini 3 Pro, Mini 4 Pro |
| DJI Mavic Pro | Mavic Pro |
| DJI Mavic 2 | Mavic 2 Pro, Mavic 2 Zoom |
| DJI Mavic 2 Enterprise | Mavic 2 Enterprise Dual |
| Mavic 2 Enterprise Advanced | |
| DJI Mavic 3 | Mavic 3 Pro, Mavic 3 Classic, Mavic 3 Enterprise |
| Mavic 3 Multispectral | |
| Mavic 3 Thermal | |
| DJI Phantom 3 | Phantom 3 Advanced, Phantom 3 Pro |
| DJI Phantom 4 | Phantom 4, Phantom 4 Pro, Phantom 4 Pro V2, Phantom 4 RTK |
| DJI Spark | Spark |
| DJI Matrice 100 | Matrice 100 |
| DJI Matrice 200 Series | Matrice 200, 200 V2 |
| DJI Matrice 210 Series | Matrice 210, 210 RTK, 210 V2, 210 V2 RTK |
| DJI Matrice 300 | Matrice 300 RTK |
| DJI Matrice 30 | Matrice 30T |
| DJI Matrice 600 | Matrice 600 |
| DJI Matrice 4/4T | Matrice 4, Matrice 4T |
| Parrot Anafi | Anafi, Anafi AI, Anafi USA |
| Parrot Anafi Thermal | Anafi Thermal |
| Yuneec | Supported models (e.g., H520, Typhoon) |
| AgEagle eBee | eBee series |
| Albris | Albris |
| AeroVironment | Quantix |
| Autel EVO | EVO I, EVO II 8K, EVO II Pro 6K, EVO II V3/Dual/Enterprise |
| Skydio | Skydio 2, 2+ |
| Skydio X2, X10 | |
| Wingtra | Wingtra |
| Delair | UX11 |
| ACSL | Soten |
| MAPIR | MAPIR |
| XAG | M500 |
| Freefly | Supported models |
Flight Controller Apps for Drone Capture
The following flight controller apps are commonly used for drone capture. Other apps not listed here may also be compatible.
Important: Always check the official app documentation to confirm support for your specific drone model, and ensure that your controller is compatible before use.
| Name | Description | Official Links |
|---|---|---|
| DJI Fly | Latest DJI app for consumer drones | [DJI Fly (Official)] · [App Store] |
| DJI GO 4 | Legacy DJI app (Phantom, early Mavic, Inspire) | [DJI GO 4 (Official)] · [App Store] |
| Litchi | Mission planning and waypoint flights for DJI drones | [Litchi Official] · [DJI Monitor Guide] |
| Dronelink | Automated flights and mission chaining for DJI / Autel drones | [Official Site] · [Android] · [iOS] |
| 3Dsurvey / 3Dsurvey Pilot | Photogrammetry and 3D mapping/survey software | [3Dsurvey Official] · [3Dsurvey US] · [Android Pilot] |
| Skydio App | Consumer app for Skydio 2 / 2+ (flight control, tracking, cinematic skills) | [iOS] · [Android] |
| Skydio Enterprise App | Enterprise-grade app for autonomy, inspections, 3D scan, and advanced missions | [iOS] · [Android] |
Drone Capture Best Practices
The following best practices help ensure consistent image coverage and reliable processing results when capturing drone photos .
Flight Pattern and Image Overlap
Plan your drone capture using a grid-based flight pattern to ensure even site coverage and sufficient image overlap.
- Fly parallel paths across the site
- Maintain consistent spacing between flight lines
- Capture images at regular intervals along each path
-
Maintain a consistent flight height throughout the capture
Note: When multiple flight passes are required, keep the height consistent within each pass and avoid frequent or unplanned height changes.
This capture pattern helps achieve the overlap required for reliable processing.
Recommended minimum overlap
- Front overlap: 75% or higher
- Side overlap: 60% or higher
Note: For flat areas with homogeneous visual content (such as agricultural fields or concrete surfaces), increase front and side overlap to at least 80% to ensure reliable image alignment.
Insufficient overlap is one of the most common causes of processing failure or inaccurate results.
Considerations for Oblique Capture
When using oblique capture, maintaining consistency is especially important to ensure reliable 3D reconstruction.
When capturing buildings or vertical structures:
- Use intentional, structured flight passes rather than free or random movement
- If multiple passes are required, make angle or distance changes between passes, not continuously
- Keep the camera angle and flight height consistent within each pass
- Ensure sufficient overlap along façades and vertical surfaces
This approach helps ensure vertical surfaces are captured clearly and can be reconstructed reliably in 3D outputs.
Image Sharpness and Lighting
Maintain stable flight and lighting conditions to capture clear, usable images.
- Fly at a steady speed to reduce motion blur
- Capture images in consistent lighting conditions across the site
- Avoid capture during low-light conditions or when strong glare is present
Camera Settings
- Use default camera settings unless image quality issues occur
- If needed, adjust settings to reduce blur or noise and avoid heavy image enhancement
GCP Target Best Practices
If you plan to use Ground Control Points (GCPs) to improve georeferencing accuracy, follow these best practices when placing GCP targets on site and capturing drone images over them.
Note: GCPs are optional. GPS-based georeferencing is used by default. GCPs are recommended for civil and survey workflows that require higher positional accuracy.
GCP Target Requirements
- Target pattern: Black and white, square or diagonal pattern with high contrast.
- Minimum target size: 50 cm (20 inches). Targets must be large enough to be clearly visible in drone images.
- Minimum number of GCPs: 3 targets. More GCPs generally improve accuracy and allow better error distribution.
GCP Placement Guidelines
- Distribute GCPs evenly across the site to provide balanced spatial coverage.
- Place GCPs on flat, stable surfaces where they will remain undisturbed during the flight.
- Ensure each GCP is visible in multiple drone images from different positions to support reliable triangulation.
- Measure each GCP’s 3D coordinates (X, Y, Z) using RTK GNSS, Total Station, or equivalent survey equipment.
Drone Image Requirements for GCP Detection
When capturing drone images over GCP targets:
- Image quality: Sharp and high contrast. Avoid blurry or overexposed images.
- Camera angle: Nadir or slight oblique (less than 30°). Steep oblique angles reduce detection reliability.
- Image overlap: Good overlap (greater than 75%) over GCP target areas.
Auto GCP Detection Scope
Drone Capture uses Auto GCP Detection to automatically identify GCP targets in drone images during processing.
- The detection algorithm searches within a 5×5 m range of the uploaded GCP coordinates.
- If detection fails for a GCP, that GCP is not applied during processing.
- Manual tie points are not supported.
Note: For details on uploading GCP coordinates and reviewing detection results, refer to the Upload drone photos with CupixConnect and Drone Capture Editor articles.
Common Capture Mistakes to Avoid
Below are some common issues to watch for during drone capture:
- Mixing nadir and oblique images unintentionally
- Flying too fast, resulting in motion blur
- Capturing images with insufficient overlap
- Changing flight height frequently or unintentionally during capture
- Capturing images with GPS location data disabled
- Using GCP targets that are too small, low contrast, or partially obscured