[toc]
Introduction
A drone capture shows the whole site from above on one date: a to-scale aerial image (orthomosaic), a 3D model of the site, the route the drone flew and, when the survey team placed them, the ground control points (GCPs) that tie the data to real-world coordinates. In SiteView a drone capture sits alongside your 360 captures, so you use the same date selector, Capture Grid, Measure and Settings to work with it.
Opening a drone capture
From the topbar
Drone captures belong to the Site, not to a building.
- Open the first selector in the topbar and choose Site.
- Open the second selector and choose Drone Capture. SiteView switches to drone mode and opens the newest drone capture.
- a Ground Capture or Drone Capture - the Site holds both kinds; pick Drone Capture to see the site from above. If only Ground Capture is listed, the project has no published drone capture yet.
When there is more than one flight on a date
Choose See other dates on the date chip. The strip that opens shows every drone capture, one thumbnail per flight, even when several were flown on the same day. Click a thumbnail to open that flight.
- a One thumbnail per flight - five flights from Apr 3, 2026 appear side by side; the highlighted one is open.
- b Output icons - which outputs that flight has: orthomosaic, DSM, point cloud and 3D mesh.
From Capture Grid
Capture Grid lists the Site's drone captures in their own row, Drone Capture, one cell per date. Click a cell to open that date.
- a Drone Capture row - one cell per date, marked with the Drone icon from the legend at the top.
Drone 2D and Drone 3D
| View | What you see | How you move |
|---|---|---|
| Drone 2D | The orthomosaic, flat and to scale, over a map | Drag to pan, scroll to zoom |
| Drone 3D | The reconstructed 3D model of the site | Orbit, zoom and pan |
- a Start - where the drone began its flight; the waypoints are numbered in flight order.
- b End - where the flight finished. Together, Start, the numbers and End show which parts of the site the flight covered.
- c GCP marker - a ground control point; click it to see how well it matched (see Ground control points).
- d 3D - switches to Drone 3D.
- e DSM - colours the site by height (see The DSM).
- f Map controls - map on/off, back to north, zoom in, zoom out and fit the site to the screen.
The gizmo in Drone 2D is the only one in SiteView that reads compass bearings: N, E, S, W. Zooming out far enough leaves the site and shows where it is in the world, which helps with orientation.
Layers of a drone capture
A drone capture brings layers a 360 capture does not have. Each one has its own category in Settings, and several are also in the right-click menu.
The orthomosaic
Settings > Orthomosaic Images turns the flat image layer on and off with Show on 2D Viewer, and Opacity fades it against the map underneath.
The flight path
In Drone 2D the route is drawn as numbered waypoints from Start to End. In Drone 3D (the 3D button on the compass) each photo the drone took is drawn where it was taken: a green camera marker for the position worked out during processing, and a blue dot for the position the drone's own GPS reported.
- a Camera marker - one per photo, drawn where it was taken. The green marker is the Computed Position and the blue dot beside it the GPS Position.
- b GCP marker - the ground control points are drawn in 3D too.
- a Show on 2D Viewer - the numbered route over the orthomosaic and the Ref Plan.
- b Show on 3D Viewer - the camera markers in the 3D model.
- c GPS Position / Computed Position - turn either set of 3D markers on or off.
If the capture has no flight log, the Flight Path switch is greyed out. You can also toggle the path from the right-click menu (Shift+L).
The DSM - the site by height
The DSM (digital surface model) colours the site by height instead of by photo, so slopes, mounds and roofs read at a glance. In Drone 2D, click DSM beside the 3D button.
- a DSM - turns the height colouring on and off.
- b Opacity and Elevation - the histogram shows how heights are spread; narrow the range with the two handles to spread the colours over the heights you care about.
3D Maps - how the 3D model is drawn
Settings > 3D Maps controls how the model looks in Drone 3D.
- a Rendering Style - choose how the model is drawn (table below).
- b Opacity and Point Limit per Frame - fade the model, and set how many points are drawn at once (5M by default).
- c Point Size - Adaptive or Fixed.
- d Hide surfaces facing the camera - on by default.
| Rendering style | What it shows |
|---|---|
| RGB Point Cloud | The model in its real photo colours (default) |
| Textured Mesh | A solid surface model with the photos draped over it |
| Elevation Heatmap | The point cloud coloured by height, low (blue) to high (red) |
| X-Ray | A see-through rendering with presets Grayscale, Blueprint, Thermal and Night Vision |
X-Ray draws the 3D map as a see-through layer, so you can look through dense areas such as trees and roofs and see the shapes and markers behind them. In Settings > 3D Maps, set Rendering Style to X-Ray.
| Setting | What it does |
|---|---|
| Opacity | How see-through the X-Ray layer is. |
| Visual Preset | A ready-made color scheme: Grayscale, Blueprint, Thermal or Night Vision. |
| X-Ray Color | The amount of red, green and blue in the X-Ray color, for a color of your own. |
| Fresnel | Makes surfaces that face you more transparent and edges more solid, so outlines of objects stand out. Adjust Power and Alpha Multiplier. |
| Tonemapping | Controls brightness where see-through layers overlap. Use Exposure to keep dense areas from washing out. |
| Range | Draws X-Ray only up to Max Distance from your viewpoint. Anything farther is not drawn. |
Turn each parameter on with its Enable switch. Reset at the bottom of the panel returns all settings to their defaults.
- a Rendering Style - set to Elevation Heatmap.
- b Highest points in red - here the trees around GCP2 stand higher than the roofs, which is why that target was hard for the drone to see.
- a Rendering Style - set to Textured Mesh: a solid model with the photos draped over it, so walls and roofs read as surfaces.
Ground control points
Ground control points (GCPs) are targets on the ground whose real coordinates a survey team measured. When they were supplied at upload, each one is drawn on the drone capture as a labelled crosshair, and Settings > Ground Control Points shows them on the 2D viewer, the 3D viewer, or both.
Click a marker to see how it matched:
- a Blue marker - the target was found in the drone photos.
- b Given Position - the coordinate the survey supplied.
- c Computed Position - where processing placed that same target.
- d Position Error - the difference on X, Y and Z. The smaller, the better the drone capture agrees with the survey.
- a Red marker with ! - the target was not found in any drone photo.
- b This GCP target wasn't found in drone photos - only the Given Position is shown, so this point did not help place the capture.
Checking accuracy with the GCP summary
In drone mode, the info button at the top right opens Ground Control Points, a summary of how well the whole capture matches the survey.
- a Info - opens the summary.
- b RMS Error - one overall number for the whole capture, and its X, Y and Z parts. Lower is better.
- c Error Distance - each GCP's own error; a value in red stands out from the rest.
Click a row, or the marker on the map, to see that GCP's Given Position, Computed Position and Position Error.
| What you see | What it means |
|---|---|
| A small error on every GCP | The drone capture agrees with the survey; measurements off it can be trusted to that level |
| One GCP far off the others (shown in red) | That one point disagrees and pulls the overall RMS Error up. The usual cause is where the target was placed: a target right beside a building or surrounded by trees is hard for the drone to see clearly. Check that target before measuring near it |
| Not Detected on a GCP, Not available for RMS Error | The targets were not found in the photos, so no accuracy figure exists for the capture |
Working on a drone capture
Right-click menu
Right-click the 3D model for a Layers menu: SpatialNotes (Shift+N), Measurements (Shift+M), Flight Path (Shift+L), Backface Culling (Shift+B), Axis Plane (Shift+X) and Drawings.
- a Layers - each row turns one layer on or off; the shortcut is on the right.
- b Flight Path - the quickest way to hide the camera markers (Shift+L).
Measure
Measure offers the same tools as on a 360 capture: RulerBoard, Distance, Radius, Angle, Path, Area and Volume. Volume is useful on a drone capture for stockpiles and earthworks. See Measure - lengths, areas and volumes for how each tool works.
- a Measure tools - the same toolbar as on a 360 capture.
Timeline Compare
Compare splits the screen so you can set a drone capture beside another one. On the right, Change lists the other drone captures to compare against.
- a Compare - splits the screen. The left side is the capture you opened; See other dates changes it.
- b Change - picks the drone capture on the right.
- c Divider buttons - Dual Camera, Single Camera and TwinLens.
The buttons on the divider switch the layout, from top to bottom: Dual Camera, Single Camera and TwinLens. See Compare - two dates, or the model for how each works.
BIM Compare
When the project has a BIM model, BIM in the left toolbar sets the drone capture beside the model. The model opens on the right, with its name and version at the top; Change picks another model. The divider buttons switch the layout the same way as in Timeline Compare, including TwinLens, which shows the model inside a lens over the drone capture.
- a BIM - opens BIM Compare.
- b TwinLens - the model shows inside this lens, over the drone capture.
- c Model and version - Change picks another model.
Drone data in your ground captures
When you go back to Ground Capture on the Site, the orthomosaic stays under the Ref Plan, so your 360 positions sit on the aerial image. Ground Capture Settings also list 3D Maps and Orthomosaic Images next to Pano Bubbles.
- a Ref Plan with the orthomosaic - the aerial image from the drone capture sits under the walking path of your 360 captures.
- b Current position - where the 360 view above was taken, shown on the aerial image.
What a drone capture shows in Settings
Fewer categories than a building, and different ones: Reference Plans (when a reference plan has been uploaded for the Site), 3D Maps, Orthomosaic Images, Ground Control Points (when the survey supplied them) and Flight Path under Reality Captures, then Public Share and Integrations. There are no Pano Bubbles, because a drone capture has no walking positions. See Settings and SmartFilter - what is drawn.
- a Reality Captures - the drone-only categories.
Next: Compare - two dates side by side, or the model.