[toc]
Aligning puts a reference in the project's coordinates, so it lands where the building is. It works the same way for every reference: open its editor from the Library, choose a frame, place it, and mark it Aligned. A drawing has to be extracted first; a 3D BIM is ready to align as soon as it is uploaded.
Read Skeleton - sites, buildings, levels and coordinates first if BCS, PCS and CRS are new.
Choose a frame
Every reference is aligned in one of three frames.
| The reference is... | Choose | Why |
|---|---|---|
| A floor or ceiling plan of one building, or that building's model | BCS | It should follow the building if the building is moved or rotated. |
| A site plan, or anything covering several buildings | PCS | It belongs to the project, not to any one building. |
| Already geo-referenced: real coordinates in the file | CRS | It is pinned to the world and stays put when you edit the PCS or a BCS. |
Align a drawing
Open the drawing in its editor, select it in the DRs tab, and open Alignment on the right.
- Choose the Coordinate Reference Frame.
- Choose Direct placement (you set origin, scale and rotation) or Anchor-based (Solver) (you link points on the drawing to anchors). The solver needs at least one anchor in the chosen frame; until then the tab says Add a BCS anchor in the Anchors panel first (or PCS, or CRS) and offers Open Anchors panel.
- For direct placement, set the Scale: Metric, Imperial or Custom. Calibrate by picking two points works it out from a known distance.
- Set the Origin: the point in the drawing that maps to (0, 0) of the frame. Type X and Y, or use Pick on canvas. On the canvas, (0, 0) is where the red and green axes cross. In CRS, you pick a point and enter its Latitude, Longitude and Altitude instead.
- Set the Rotation: the angle clockwise from the frame's +Y.
- Click Mark as Aligned, then Save.
- Coordinate Reference Frame - BCS, PCS or CRS.
- How to place it - Direct placement or Anchor-based (Solver).
- The solver's prerequisite - an anchor in the chosen frame; Open Anchors panel adds one.
- Scale - Metric, Imperial or Custom; calibrate from two points a known distance apart.
- Origin - the point in the drawing that maps to (0, 0); type it or pick it on the canvas.
- (0, 0) - where the red and green axes cross.
You can fine-tune an Activated drawing's alignment later without losing its status or its published state.
The drawing's Properties tab
Properties shows the reference at a glance: the Status rail (Draft, Aligned, Activated), the Mounts list with Edit, and the Flags: Aligned, Activate and Lock Transformation. Mask below them trims how much of the page is shown.
- The file and the reference - which source file is open, and which reference.
- The reference in the DRs tab - everything taken from this file.
- The drawing - placed in its building's frame.
- Status - Draft, Aligned, Activated.
- Mounts - where it is attached; Edit changes that.
- Flags - Aligned, Activate, and Lock Transformation (stops it moving by accident).
- Close and Save - nothing is kept until Save.
Align a 3D BIM
Open the model in its editor and open Alignment on the right. A model is aligned in its building's frame, Origin (BCS).
| Setting | What it does |
|---|---|
| Manual selection | You set the origin yourself: pick faces or grid lines for Horizontal (X-Y) and Height (Z) with Set up. Both are required. |
| Shared Coordinate | Takes the position of a model that is already aligned. This is how the architectural, structural and MEP models of one building line up without aligning each by hand. |
| Custom origin | Where the origin goes: BCS Origin (0,0), or an Existing Anchor. |
| Rotate around the Z-axis | Turns the model to match the building. |
| Add offset | Adds an offset to the origin. |
- Choose Manual selection or Shared Coordinate.
- Set the origin and, if needed, the rotation and offset.
- Click Mark Aligned, then Save.
Properties also holds Adopt Survey Point as the Building's geo-reference, which lets the model's own survey point set where the building sits on the map. See 3D BIM for the editor's other tabs.
Use anchors
An anchor is a named point tied to a frame (a building's BCS, the project's PCS, or real-world CRS coordinates). Place it once, then align later drawings to it with Anchor-based (Solver); a model can use one as its Existing Anchor origin. See Anchors.
Apply an alignment to other references
Most projects align the same plan over and over; a tower repeats one floor plate twenty times. Align one reference, then hand its alignment to the rest.
- Open the aligned reference's menu in the editor (or the source file's menu in the Library).
- Choose Apply this alignment to other DRs.
- In the dialog, Source is the reference you are copying from; each row says Aligned or Not aligned. Under Target DRs, tick the references to receive it, grouped by source file, with Select all. A target already positioned is marked Aligned - will overwrite.
- Apply.
Position, rotation and scale are copied; anchors are not; and targets must be the same kind as the source. A nine-page plan set becomes nine drawings: align one, apply it to the other eight, then mount each to its level.
- The reference's menu - the three dots on the reference.
- Apply this alignment to other DRs - copies this reference's position, rotation and scale to others.
Next: Anchors - known points to align against.