[toc]
An anchor is a named, known point, such as a grid intersection or a column corner. You place it once and then align other drawings against it, so every drawing that shares the anchor lines up in the same place.
An anchor belongs to a coordinate frame, not to the drawing you happened to have open when you made it. You can add and use anchors from any drawing in the editor, and every reference aligned in the same frame can use them.
BCS, PCS and CRS anchors
| Frame | What the anchor is tied to | Typical use |
|---|---|---|
| BCS | One building. Each building has its own BCS, so a project can have several sets of BCS anchors. The position is relative to that building. | A high-rise: set up the level 1 plan, add an anchor on a point every floor shares, then align each later floor plan to the same anchor. |
| PCS | The project. There is one PCS per project, set when the project is set up. The position is absolute within the project. | A point that site plans and plans covering several buildings are aligned to. |
| CRS | Real-world coordinates. You already know the point's latitude, longitude and altitude. | A survey point with known coordinates: enter it, then align that part of the drawing to it. |
Read Skeleton - sites, buildings, levels and coordinates for how BCS, PCS and CRS relate.
The Anchors panel
Open any drawing in its editor from the Library, then click the crosshair button in the toolbar, or Open Anchors panel on the Alignment tab.
- BCS, PCS, CRS - anchors grouped by frame, with a count on each. On the BCS tab, Building picks whose anchors you see.
- The anchors - each row shows the name, the geometry, the coordinates, who made it and the frame. The eye shows or hides it on the canvas; the menu holds Edit... and Delete.
- On the canvas - anchors appear as labelled markers on the drawing.
- Anchor scope - with Anchor-based (Solver), the building whose anchors the drawing is aligned to.
- Points to Anchors - each mapping links an anchor to the matching point on this drawing.
Add an anchor in BCS or PCS
- Open the BCS or PCS tab and click + Add anchor in BCS (or PCS).
- For BCS, choose the Building (a).
- Leave the Geometry on Point (b). Point is what anchors normally use; Plane and Measurement are also offered.
- Give it a Name people will recognize, for example Grid A1/B1 (c).
- Click Pick on Canvas (d), then click the point on the drawing.
- Building - the building whose BCS the anchor belongs to. Not shown for PCS.
- Geometry - Point. Plane and Measurement are also available.
- Name - shown on the canvas and in the anchor list.
- Pick on Canvas - then click the point on the drawing to place the anchor.
Place an anchor on a point you will be able to find on the other drawings too, such as a grid intersection, and on a drawing that is already aligned, so the anchor's coordinates are right.
Add an anchor in CRS
A CRS anchor is a real-world position, so you type it rather than pick it.
- Open the CRS tab and click + Add anchor in CRS.
- Give it a Name. The geometry is Point.
- Enter its Latitude and Longitude in degrees and its Altitude in meters (EPSG:4326). Picking on the canvas is not available for CRS anchors.
- Click Add.
Align a drawing to anchors
With Anchor-based (Solver) you do not type an origin, scale or rotation. You tell the solver which point on the new drawing matches which anchor, and it works out where the drawing goes. The example below aligns a level 2 plan to two BCS anchors placed on the level 1 plan of the same building.
Before you start
- The anchors already exist in the frame you will align in, placed on a drawing that is already aligned.
- Each anchor is on a point you can find on the new drawing too, such as a grid intersection or the corner of a stair core.
- Use two or more anchors, far apart. With one mapping only the position is solved; two or more also set the scale and rotation, and the further apart they are, the more accurate the result.
Link points to anchors
- Open the new drawing in its editor, select it in the DRs tab, and open Alignment.
- Choose the Coordinate Reference Frame the anchors are in. A new drawing starts on PCS, so switch to BCS for a floor plan.
- Choose Anchor-based (Solver). Under Anchor scope, check the building.
- Under Points to Anchors, click + Add mapping. The canvas waits for a point: zoom in and click the feature on this drawing that matches the anchor. The row shows Picked.
- In the same row, choose the Anchor. Only Point anchors are listed. A dashed arrow now runs from the picked point to its anchor (a).
- Repeat for the second anchor (b). Linked Anchors lists the anchors in use; to redo a pick, remove the row with its X and add it again.
- Picked points and anchors - each dashed arrow runs from the point picked on this drawing to its anchor. The grey line between the anchors shows their distance (14.39 m).
- Points to Anchors (2) - each row pairs an anchor with a point picked on the drawing.
- Solve Transform - works out the placement from the mappings.
Solve and check
- Click Solve Transform (c). The drawing moves, turns and scales so that each picked point sits on its anchor, and a message confirms that the origin, scale and rotation were calculated.
- Check the result (a): the picked points sit on the anchor markers, and walls and grid lines fall where they should. The numbers appear under Transform (b): Origin X, Origin Y, Scale (m/px), Rotation (°) and Z-offset (m). Adjust them if needed, or redo a mapping and solve again.
- Click Mark as Aligned (c). The status changes from Draft to Aligned.
- Click Save.
- The result - the drawing has moved, turned and scaled so the picked points sit on Point 1 and Point 2.
- Transform - the calculated origin, scale and rotation (here 16.56°), which you can adjust.
- Mark as Aligned - confirms the placement; then Save.
Next, mount the drawing on its level. See Mount and publish.
Anchors are also used as the custom origin (Existing Anchor) when you align a 3D BIM, and with Pick anchor in the Skeleton.
Next: Mount and publish - attach the aligned references to their nodes and show them in the apps.