[toc]
SmartFilter, on the gizmo in aerial mode, cuts the 3D map down to the part you care about. To turn layers on and off and set how they look, see Settings.
SmartFilter separates a 3D capture into the things it is made of, and lets you show only some of them, pick levels, or cut the model open.
Opening SmartFilter
SmartFilter works on the 3D map and on drone captures. It does nothing in first-person mode.
- Click Aerial mode on the gizmo.
- Click SmartFilter, the bottom-right button of the gizmo.
- Pick a tab: Segments, Multi-Level or Clipping.
Drag the handle at the top left of the panel to move it out of the way.
Segments
The labels come from Gen6 SLAM: every point in a 3D capture is labelled during processing, with nothing to switch on. The labels say what a thing is, not its condition, so they do not flag corrosion, cracks or other surface defects. The percentages are for the capture and levels you have loaded and change from capture to capture, so read them as proportions, not as measurements.
Segments filters the points by what was detected in them. The panel lists each class with the share of the capture it accounts for, largest first. On a classified building level it reads like this: Wall 29%, Ceiling 28.4%, Floor 23%, Beam 6.3%, Debris / Clutter 5.8%, Pipe / Duct 2.2%, Railing 1.4%, Equipment 1.2%. A plant room reads differently: Energy Facility Level 1 is mostly Wall, Floor and Ceiling, then Equipment, Pipe / Duct, Railing, Electrical Box and Conduit.
- Clear the classes you do not want to see.
- Tick Select All to bring every class back.
- Turn on Show unselected in true color to keep the cleared classes on screen in their original colours, instead of hiding them.
- Select All - ticks or clears every class at once.
- The classes - Wall, Ceiling, Floor, Beam, Debris / Clutter, Pipe / Duct, Railing, Equipment, each with its share of the points; untick one to hide it.
- Show unselected in true color - on: hidden classes stay visible in photo colour; off: they disappear.
- The dollhouse in class colours - each point coloured by what it is.
The full set is twenty labels, and it is the same twenty everywhere: one flat list, no groups above it. If your capture shows fewer, none are missing. Labels that do not occur in the capture, or that belong to levels you have not loaded, are shown greyed out and marked Not in loaded levels. Load more levels and they come back.
Multi-Level
Multi-Level brings the 3D models of other levels in beside the one you are on, for full-building context. Tick the levels you want; a multi-storey building can then be shown one level at a time or several together.
Levels come in as they load, so give a large building a moment. The tab only has something to offer when the capture has data on more than one level.
- Levels you can bring in - tick L3 to draw it under L4.
- L4 with L3 underneath - the building in context.
Clipping
Clipping cuts the model along three axes so you can see inside it. Each axis has two handles:
| Slider | Cuts from |
|---|---|
| Bottom / Top | Below and above, to see one storey or look under a ceiling |
| Front / Back | The front and the back |
| Left / Right | The two sides |
Drag a handle in to cut. The figure above each slider is the width that is left, and the figures under it are where the two cuts sit. A box drawn around the model shows what is kept.
Reset puts every cut back to the full extent.
- Bottom / Top - the top handle dragged down, so the ceiling is cut away.
- Front / Back - cut from the front or the back.
- Left / Right - cut from either side.
- Relative Range - shows the handles as distances from the model instead of coordinates.
- Reset - puts the box back around the whole model.
- The clipping box - what is left inside it is drawn.
What SmartFilter does not label
SmartFilter labels what a thing is, never what condition it is in. The twenty classes are building elements: floor, wall, duct, column. Nothing here marks corrosion, water damage, concrete defects, spills or cracks, and there is no confidence score on a class.
Changes from 4.0
| In 4.0 | In 5.0 |
|---|---|
| Not in 4.0 | New: SmartFilter, on the gizmo, with Segments, Multi-Level and Clipping |
Next: Compass - ask questions about your site.